Knowledgebase
 
1). There is a black knob on the top of the CBS-630, as seen in the (IMG.'s 1&3) attached photo, that has to be removed. This can be done by twisting that knob to the left until it is no longer seated in the top of the CBS-630. (IMG.'s 4&5) 2). Directly...
Attached you will find the photos that will correspond with my instructions, in photo's. * First you're going to remove the screws that hold the metal plate in place as seen in PHOTOS 1 AND 2. * Secondly you're going to remove the plate to gain acce...
Attached you can see a step by step photo sequence of replacing the heating element for your vacuum packaging machine. It is highly advised to take progressive pictures as you remove components as it makes reassembly simplistic. 1. As seen in the images...
Here is small video tutorial of how to set up the functions of Coder Printer ( Please Click Link Or Copy Paste) https://youtu.be/CWbAXHZLot0 [https://youtu.be/CWbAXHZLot0]
1) Located on the shaft there is a set screw that actually connects the drive shaft to the conveyor housing. (IMAGE 6). 2) This screw is probaly loose therefore the shaft though is rotating, is only free spinning. 3) Stop the machine!!! 4) To tighte...
TROUBLESHOOTING INTRUCTIONS * Initially if you remove the 4 small screws holding the face plate in place, you will gain access to the machines internals, there you will find the fuse holder has two contacts that have sleeve protectors on them. These ...
The ground wire connected to the motor on the CBS is the yellow and green wire. It should be connected from the motor to the frame of the CBS. This can be seen the attached photos.
The cycle speed can be adjusted by adjusting the small black knobs on top of the main piston housing. Adjusting one may require an adjustment to the other one to achieve and maintain a smooth cycle flow. This is adjusted according to the size of the conta...
You will know if the gap is correct because the bag would have sealed properly and not jammed or cause degredation to the integrity of the product you're sealing. The product should fit snug into the infeed bands as to not fall out or become dislodged. Al...
1) Locate the shaft and follow it back to where it connects to the housing in the actual machine you will find at the base a fastner nut as seen in _IMAGE_ 7. 2) If you're looking to adjust the height of the actual shaft you would need to loosen that nu...
Replacing the heating wire in a SHR model is very simple. Preferably you will need long nose pliers. The heating wire mounts on spring loaded terminals. You must find the terminals on each end of the arm first. Each terminal has a hook like end where t...
The compressor must have a minimum tank size of 25 GALLONS and be able to deliver 4 CFM (CUBIC FEET OF AIR PER MINUTE) AT 90 PSI (PRESSURE PER SQUARE INCH). Please note just because a compressor can reach 150 psi does not mean it can maintain that pressur...
Although there is an option for alarms to be set on the digital panel, it is not applicable for standard sealing use. This alarm option is compatible with a variety of larger scale processes where you would need to troubleshoot this machine in conjunction...
Make sure that you're not using the self clean button to seal and cut the bags. Check the element to make sure that no residue is on the element, or left behind around the element.
If the teflon belts are breaking/ stripping it could be an issue of 2 possible root causes. The belts could be adjusted to closely togethter and when the product is ran through the infeed guide. The tightness causes the belts to strip. Or the actual bag t...
The wires of the floor scale are internally wired and are wired from the respective load cells to the main distribution block located internally. You will find 2 allen bolts securing the back plate on the machine, after removing this place you will find t...
Trouble shooting CBS 630/730 power Checking for power situation: (Each number represents a new trouble shooting technique) 1) Check fuse (under main power connection area) 2) check the E-stop button, toggle on and off few times to see if it's faulti...
* Initially you should check the oil level in the motor to make sure the level is sufficient for usage. * Secondary you need to compare the room temperature and the operating temperature for the machine because concerns are that room may be too col...
An Impluse Sealer that has the cutting feature will have a cutting distance from the seal of 3/4". So from the edge of the seal to where the cut is made will measure 3/4".
The size for the compressors hose connector is 1/4". So you will be looking for a fitment of 1/4".
The fuses on the CBS can be found on the same connector as the main power male reciprocal. Please refer to the photos attached for pictures of where to find these.
Most popular articles 
 
Newest articles